La-crosse-technology Radio Controlled Projection Alarm WT-5110 Uživatelský manuál

WT-5110 433 MHz Radio Controlled Projection Alarm Instruction Manual

10 H. CHANGING DISPLAY MODE (INDOOR TEMPERATURE/HUMIDITY OR ALARM TIME) There are two possible display modes in the indoor temperature/humidity se

11SPECIFICATIONS FOR WT-5110 Temperature: Measuring range: 14°F to 99°F with 0.2°F resolution Checking intervals: Every 10 seconds Humidity Measuri

12WARRANTY INFORMATION La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing defects in materials and

13For warranty work, technical support, or information contact: La Crosse Technology, Ltd 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.16

1WS-9117U Wireless 433 MHz Temperature Station Instruction Manual

2TABLE OF CONTENTS Topic Page Inventory of Contents 3 Quick Setup 4-8 Detailed Setup Guide Battery Installation 9-11 Setting the Time 11-12 Sel

3INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2) 3. 3

4QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote tempera

5In this time the indoor temperature station and remote temperature sensor will start to talk to each other and the display will show both the indoor

6of resistance. Your distance plus resistance should not exceed 80 ft. in a straight line. NOTE: Fog and mist will not harm your remote temperature

2TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Bat

7b. When you have your choice shown on the display press and release the “SET/CH” button once. 2. Degree Fahrenheit will now show. a. To change b

8the word TIME when in the PM hours. During the AM hours this area will be blank. b. When the correct hour is shown, press and release the “SET/CH”

9 DETAILED SETUP GUIDE I. BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket. 2. Remove battery cover 3. Observing

10B. INDOOR TEMPERATURE STATION Note: After the batteries are installed, DO NOT press any buttons. This may interfere with the signals, causing tem

115. The indoor temperature station should now show: “-:- -” in the TIME LCD, and temperatures in the INDOOR and OUTDOOR LCD’s. II. TIME A. SETT

125. Press and release the “SET/CH” button to move to the minute setting 6. Press and release the “MIN/MAX” button to set the minutes. 7. Press and r

133. Press and release the “MIN/MAX” button to shift between °F and °C. 4. Press and release the “SET/CH” button twice to activate settings. IV. FEA

14seconds. C. ADDING ADDITIONAL REMOTE TEMPERATURE SENSORS (OPTIONAL) 1. The WS-9117U is able to receive signals from 3 different remote temperature

15remote temperature sensor units, and in numeric sequence. Second, install batteries into the indoor temperature station. Transmission problems wi

16D. VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS 1. To view the temperature of a different remote temperature sensor unit, pr

3INVENTORY OF CONTENTS 1) WT-5110 Alarm Clock 2) AC adapter/transformer 3) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not include

17V. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sen

18that is required is to place the indoor temperature station in an appropriate location. 2. To wall mount, remove the table stand. To do this, pull

19TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnolo

20Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to with

21 MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean displa

22SPECIFICATIONS Transmitting Frequency 433MHz Measuring Temperatures Indoor Temperature Station: Indoor 32°F to 140°F with 0.2°F resolution. (0°C

23Temperature Station Dimensions: (H x W x D) Indoor Temperature Station 5 x 2.25 x 1 in (excluding table stand) (125 x 58 x 23 mm) Remote Temper

24purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center. La Crosse Technology, Ltd will repair or replace t

25be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4) damage resulting from failure to follow

26consequential or incidental damages therefore the above exclusion of limitation may not apply to you. For warranty work, technical support, or inf

4QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. We recommend beginning the set-up procedure at

27 Freq. 433.92 MHz La Crosse Technology Made in China WS-9117U FCC ID: OMO-01RX (Receiver), OMO-01TX (sensor) THIS DEVICE COMPLIES WITH PART 15 OF

5DETAILED SET-UP GUIDE I. BATTERY INSTALLATION A. PROJECTION ALARM 1. Remove the battery cover. 2. Observe the correct polarity, and install 2

6II. PROGRAM MODE To enter the Program Mode hold down the “MODE/MIN” button for 3 seconds, until the time flashes in the top of the display. The Pr

74. Press and release the “MODE/MIN” button to select the appropriate time zone. There are 24 time zones to choose from (based relative to the int

8III. FEATURES & OPERATIONS A. FEATURES 1. Radio-controlled time 2. Projection of time 3. LED backlight 4. Display of indoor temperature/hum

9D. LED BACKLIGHT 1. The projection alarm has an LED backlight designed for night-viewing. This will light up for 4 seconds whenever the snooze bu